accessories for infrared detectors heatsinks for te-cooled detector chopper, etc. temperature controllers wide lineups of accessories for infrared detector www.hamamatsu.com 1 hamamatsu provides temperature controllers, heatsinks f or te-cooled detector, chopper and cables, etc as accessories for in- frared detectors. connection example of accessories for infrared detectors kaccc0321ec * 3 * 2 * 1 chopper driver circuit (accessory of the c4696) heatsink for te-cooled detector a3179 series amplifier for infrared detector * 4 c4159/c5185 series c3757-02 temperature controller c1103 series power supply (15 v) power supply (100 v, 115 v, 230 v) ?c power supply (+12 v) chopper c4696 te-cooled detector* 3 power out gnd +12 v power chopper trig measuring instrument * 1: attach the bare wire ends to a 3-pin or 4-pin connector or to a banana jack, and then connect them to the power supply. * 2: soldering is needed. when using the c5185 series ampli er, a bnc connector (prepared by the user, example: one end of the e2573) is re- quired. * 3: no socket is available. soldering is needed. * 4: refer to the datasheet ?ampli ers for infrared detectors? for detailed information. note: refer to page 6 for details on cables.
accessories for infrared detectors temperature controllers, heatsinks for te-cooled detector, chopper, etc. 2 speci cations absolute maximum ratings parameter c1103-04 c1103-05 c1103-07 applicable detector * 5 one-stage/two-stage te-cooled type pbs, pbse photoconductive detector, inas photovoltaic detector, ingaas, si photodiode two-stage/three-stage te-cooled type mct, insb photoconductive detector one-stage te-cooled type mct, insb photoconductive detector setting element temperature -30 to +20 c -75 to -25 c -30 to +20 c temperature stability within 0.1 c output current for temperature control 1.1 a min., 1.2 a typ., 1.3 a max. power supply 100 v 10 % 50/60 hz * 6 power consumption 30 w dimensions 107 (w) 84 (h) 190 (d) mm weight 1.9 kg approx. accessories instruction manual 4-conductor cable (with a connector, 3 m) a4372-05 * 7 , power supply cable * 5: it doesn't correspond to te-cooled type infrared detector module with preamp. * 6: please specify power supply requirement (ac line voltage) from among 100 v, 115 v and 230 v when ordering. *7: when used in combination with an a3179 series heatsink, do not use the 4-conductor cable supplied with the a3179 series, but us e the a4372-05 instead. parameter value operating temperature +10 to +40 c operating humidity 90% max. * 8 storage temperature -20 to +40 c *8: no condensation note: ex ceeding the absolute maximum r atings even momentarily may cause a drop in product quality. always be sure to use the product within the absolute maximum ratings. block diagram kirdc0008eb temperature controllers c1103 series the c1103 series is a temperature controller designed for thermoelectrically cooled infrared detectors. the c1103 series allows easy but accurate temperature setting for the thermoelectric cooler mounted in an infrared detector. te-cooled detector thermistor te-cooled element comparator c1103 series amp circuit current circuit power supply ac input
accessories for infrared detectors temperature controllers, heatsinks for te-cooled detector, chopper, etc. 3 kirda0018ed heatsinks for te-cooled detector (to-8, to-3 package) a3179 series these heatsinks are designed for use with thermoelectrically cooled detector sealed in a 6-pin to-8, to-3 package. the cooling (heat dissipation) capacity of the a3179 and a3179-03 is about 35 c relative to the ambient temperature 25 c, the a3179-01 is about 40 c, and that of the a3179-04 is about 85 c. the a3179-03 is designed only for two-color detector k3413 series, the a3179, a317 9-01 for to-8, the a3179-04 for to-3 (heatsink for to-66 is available as a custom product.) . dimensional outlines (unit: mm, tolerance unless otherwise noted: 0.3) a3179 accessories instruction manual 4-conductor cable (2 m): for te-cooler and thermistor * 9, * 10 coaxial cable (2 m): for signal * 10 32 60 (4 ) ?3.5 3 ?26 0.2 3 * 1 0.4 0.3 * 2 weight: 50 g approx. ?32 32.6 ?46 ?40 photosensitive surface* 3 *1: bottom surface (reference surface) of detector metal package *2: when the detector is installed *3: the position of the photosensitive surface differs according to the detector used. refer to the dimensional outline for the detector. detector metal package * 9: when used in combination with a c1103 series temperature controller, do not use the 4-conductor cable supplied with the a3179 series, but use the 4-conductor cable a4372-05 (sold separately, with a connector). * 10: no socket is supplied for connection to infrared detectors. connect infrared detectors by soldering. cover the soldered joints and detector pins with vinyl insu- lating tubes.
accessories for infrared detectors temperature controllers, heatsinks for te-cooled detector, chopper, etc. 4 a3179-04 a3179-01, a3179-03 a3179-01: b=6 a3179-03: b=6.4 weight: 53 g approx. 32 60 ?40 ?32 ?26 0.2 ?46 b 3 36 (4 ) ?3.5 detector metal package photosensitive surface* 3 * 1 0.4 0.3 * 2 *1: bottom surface (reference surface) of detector metal package *2: when detector is installed *3: the position of the photosensitive surface differs according to the detector used. refer to the dimensional outline for the detector. 56 68 80 56 40 45 photosensitive surface 6.7 0.5 3 0.5 ?38 0.5 (4 ) ?3.5 0.5 fixation board ?19.7 +1 -0 weight: 320 g approx. kirda0019ed kirda0149eb
accessories for infrared detectors temperature controllers, heatsinks for te-cooled detector, chopper, etc. 5 kirda0022ea chopper c4696 dimensional outline (unit: mm, tolerance unless otherwise noted: 1) speci cations parameter speci cation chopping frequency * 11 115 to 380 hz, 345 hz typ. * 12 power supply (v d ) dc 5 to 13 v, 12 v typ. duty ratio 1 : 1 rotational stability 0.06 %/c synchronous signal (high level) min. v d - 0.5 v max. v d - 0.2 v operating temperature 0 to 50 c maximum current consumption * 12 90 ma accessory magnet stand a1447 *11: chopping frequency will be 230 to 760 hz when an optional disc is used. *12: v d =12 v 18 13.5 38.5 bnc a1447 (magnet stand) 23.0 45.0 19 202.3 to 272.3 (adjustable) output window ?8.0 input window ?4.0 12.5 17.5 30 +12 v on-off gnd 6-pin receptacle cord length: 2 m (for connection to driver circuit) 12.5 25 37 60 6-pin connector trig counter 85 ?88
accessories for infrared detectors temperature controllers, heatsinks for te-cooled detector, chopper, etc. 6 kirdb0376ea chopping frequency vs. operating voltage operating voltage (v) 246810 14 12 100 0 (typ.) 800 700 600 500 400 300 200 chopping frequency (hz) when used with optional disk c4696 cables a4372 series cable no. cable length approx. note ? coaxial cable (for signal) 2 m supplied with heatsink a3179 series. when using this cable, make it as short as possible (preferably about 10 cm). ? 4-conductor cable (with a connector) a4372-05 3 m supplied with temperature controller c1103 series. this cable is also sold separately. ? 4-conductor cable (with a connector) a4372-02 2 m this cable is supplied with the c4159/c5185 series ampli ers for infrared detectors, c3757-02, and infrared detector modules with preamp (room temperature operation type). this cable is also sold separately. besides this cable, the a4372- 03, which is a 6-conductor cable (with connector) supplied with ?infrared detector module with preamp?, is also sold separately. ? bnc connector cable e2573 1 m option ? power supply cable (for temperature controller) 1.9 m supplied with temperature controller c1103 series ? chopper driver cable (connected to chopper) 2 m connected to chopper ? 2-conductor cable or coaxial cable (for chopper power supply) 2 m or less prepared by user
accessories for infrared detectors temperature controllers, heatsinks for te-cooled detector, chopper, etc. 7 kirda0017ea dimensional outline (unit: mm, tolerance unless otherwise noted: 1) magnet stand a1447 this is a magnet stand (sold separately) designed for the b749 photon drag detector. 1/4-20unc 100 ?20 49.5 160 min. 230 max. 5.5
accessories for infrared detectors temperature controllers, heatsinks for te-cooled detector, chopper, etc. cat. no. kacc1062e14 nov. 2014 dn 8 www.hamamatsu.com hamamatsu photonics k.k., solid state division 1126-1 ichino-cho, higashi-ku, hamamatsu city, 435-8558 japan, telephone: (81) 53-434-3311, fax: (81) 53-434-5184 u.s.a.: hamamatsu corporation: 360 foothill road, bridgewater, n.j. 08807, u.s.a., telephone: (1) 908-231-0960, fax: (1) 908-23 1-1218 germany: hamamatsu photonics deutschland gmbh: arzbergerstr. 10, d-82211 herrsching am ammersee, germany, telephone: (49) 8152-375-0, fax: (49) 8152-265-8 france: hamamatsu photonics france s.a.r.l.: 19, rue du saule trapu, parc du moulin de massy, 91882 massy cedex, france, telephone: 33-(1) 69 53 71 00, fax: 33-(1) 69 53 71 10 united kingdom: hamamatsu photonics uk limited: 2 howard court, 10 tewin road, welwyn garden city, hertfordshire al7 1bw, united kingdom, telephone: (44) 1707-294888, fax: (44) 1707-325777 north europe: hamamatsu photonics norden ab: torshamnsgatan 35 16440 kista, sweden, telephone: (46) 8-509-031-00, fax: (46) 8-5 09-031-01 italy: hamamatsu photonics italia s.r.l.: strada della moia, 1 int. 6, 20020 arese (milano), italy, telephone: (39) 02-93581733 , fax: (39) 02-93581741 china: hamamatsu photonics (china) co., ltd.: b1201, jiaming center, no.27 dongsanhuan beilu, chaoyang district, beijing 100020 , china, telephone: (86) 10-6586-6006, fax: (86) 10-6586-2866 product specifications are subject to change without prior notice due to improvements or other reasons. this document has been carefully prepared and the information contained is believed to be accurate. in rare cases, however, there may be inaccuracies such as text errors. before using these products, always contact us for the delivery specification sheet to check the latest specifications. type numbers of products listed in the delivery specification sheets or supplied as samples may have a suffix "(x)" which means preliminary specifications or a suffix "(z)" which means developmental specifications. the product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that one year period. however, even if within the warranty period we accept absolutely no liability for any loss caused by natural d isasters or improper product use. copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission. information described in this material is current as of november, 2014. kirda0021ec dimensional outline (unit: mm) valve operator for metal dewar a3515 with this valve operator, metal dewars can be re-evacuated to maintain the desired vacuum level. refer to the instruction manua l for details. please be aware that the detector performance is not guaranteed after re-evacuation is performed with the valve operator. vacuum pump valve operator metal dewar type infrared detector leak mount gland nut o-ring 80.0 1 (close) 115.0 1 (open) knob pump tube ?9.5 0.5 related information www.hamamatsu.com/sp/ssd/doc_en.html precautions ? notice technical information ? infrared detector
|
